Vehicle equipment and instruments Nissan Micra 3 (K12)

Onboard Electrical Specifications
Power (Tue) // type of lamps used (12 V) Low/high beam headlights 55/60 // H4 Front marker lights 5 Fog lights 55 // H11 Front and rear direction indicators 21 Side...

General information about on-board electrical equipment
Nissan Micra K12 vehicles are equipped with a 12 volt negative ground electrical system. All lighting fixtures and electrical units are powered by a battery recharged by...

Diagnosis of malfunctions of on-board electrical equipment — general information
The procedures and codes for diagnosing electronic control systems are discussed in Chapter Engine Electrical Systems . A typical electrical circuit may include: an...

Fuses — general information
Relay and fuse box in the engine compartment On the vehicles in question, some of the fuses are placed in the mounting block located under the cover on the left side of...

Relay — general information and function check
General information To supply power or control signal to some of the electrical consumers in the vehicle (such as fuel injection system components, horn, starter motor,...

Removal and installation of the onboard control unit (BCM)
Note. After removal, it is allowed to install only a new one, i.e. never connected to the on-board network, BCM. 1. Remove the upper section of the instrument panel (see...

Removal and installation of a horn
1. Disconnect the negative cable from the battery. 2. Remove the decorative grille (see Section Removal and installation of a decorative grille of a radiator ). 3. Give...

Removal and installation of levers of screen wipers
Windshield wipers 1. Open the hood, raise the wiper arm and remove the arm nut cover. 2. Give a nut and remove the lever, at first from outside the driver, then - from...

Removal and installation of drafts and an electric motor of cleaners of a windshield
Components for installing the e / motor and windshield wiper rods 1 - E / motor; 2, 4 - Thrust; 3 - Frame; 5 - Tip; 6 - Seal 1. Remove wiper arms (see Section Removal...

Removal and installation of the electric motor of a cleaner of glass of a door of a back
Components of installation of the e/motor of a cleaner of glass of a door of a back 1 - E / motor; 2 - Seal; 3 - Lever; 4 - Brush 1. Remove tailgate trim (see chapter...

Windscreen washer adjustment
1. To adjust the direction of the washer fluid, insert a long needle or other suitable object into the nozzle hole and turn the nozzle. 2. Adjust the position of the...

Removal and installation of hoses and washer nozzles
The layout of the nozzles and hose laying 1. To remove the washer jet windshield open the hood and, pressing on the nozzle from the side of the sprayer, turn and remove...

Removal and installation of the tank and the pump of a liquid for washing of glasses
Storage tank 1. Remove the reservoir cap and push down on the filler neck to separate it from the upper radiator support beam. 2. Remove the locker and disconnect the...

Removal and installation of the rain sensor
1. Remove the interior rear view mirror (see chapter Body ). 2. Release the tabs and pull out the rain sensor. 3. Disconnect the wiring from the sensor. 4. Installation...

Removal and installation of components of washing of lenses of headlights
Location of hoses and headlight washer nozzles 1. To remove the washer fluid pump, remove the front bumper (see chapter Body ), disconnect the pump electrical connector,...

Replacing light bulbs
Note. Incandescent lamps should only be replaced with lamps of the same type. Before replacing a lamp, make sure that the appropriate light fixture is turned off. Do not...

Removal, installation and adjustment of lighting fixtures
Note. The following is a description of withdrawals only. Installation is in the reverse order. Block headlights Note. A description of headlight alignment is given in...

Instrument cluster
Note. After removal, it is allowed to install only a new one, i.e. never connected to the on-board network, instrument cluster. Assembling the instrument cluster Lamps...

Removal and installation of trip computer and audio unit
1. Remove the central overlay of the instrument panel (see Section Removal and installation of the instrument panel and its components ). 2. Remove the screws and remove...

Removing and installing speakers and audio system antenna
The scheme of laying and fastening the antenna wire 1. To remove the speakers located in the doors, you must first remove the lining of the corresponding door (see...

Removal and installation of components of system SRS
SRS System Components 1 - Front passenger airbag unit; 2 - Driver's front airbag unit; 3 - Spiral spring; 4 - SRS control unit; 5 - Shock sensor on the left; 6 -...