Car clutch and drive shafts Nissan Terrano 1 (WD21)

Clutch and drive shaft specifications
Clutch Friction disc runout No more than 1.0 mm Deformation of diaphragm spring plane No more than 0.5 mm Torque (N·m) Clutch to flywheel bolts 19,7-27,1 Bolts of...

Clutch — general information
The clutch is located between the engine and gearbox, consists of a driven (frictional) disc, clutch cover with pressure plate and hydraulic clutch release. The drive...

Clutch pedal — removal, installation and adjustment
Removing 1. Disconnect a pusher of a main cylinder from a pedal. 2. Turn out from an arm the limiter of a pedal or the gauge of deenergizing of coupling. 3. Turn away a...

Clutch master cylinder — removal, disassembly and installation
Removing 1. Disconnect the master cylinder pusher from the clutch pedal. 2. Disconnect the hydraulic line from the cylinder and drain the fluid. 3. Turn out bolts of...

Clutch slave cylinder — removal, disassembly and installation
Removing 1. Wrap the reservoir cap with plastic wrap to prevent large fluid loss when the hose is disconnected. 2. Loosen the nut securing the hydraulic drive tube to...

Clutch damper cylinder — removal, disassembly and installation
Removing 1. Disconnect from the cylinder the fitting of the hydraulic pipes (photo), plug the pipes. 5.1 The damper cylinder is fixed to the bulkhead of the engine...

Clutch hydraulic — removal
1. Bleeding the system will be required each time after disassembling and assembling the clutch hydraulic actuator. 2. Fill the reservoir with fresh brake fluid (the use...

Details of the clutch mechanism — removal, disassembly and installation
1. Increased noise (grinding) when shifting gears or slipping of the clutch, it indicates a strong wear of the friction disc. 2. Clutch wear is highly dependent on...

Release bearing — replacement
1. When repairing or replacing clutch parts, it is necessary to replace the release bearing, or perform maintenance work on it. 2. If grease is seen coming out of the...

Gearbox input shaft guide bushing — replacement
1. The guide sleeve is a support for the input shaft of the gearbox and is pressed into a hole in the rear flange of the crankshaft. The condition of the bushing should...

Cardan shaft, gearbox and rear axle — general information
Attention! For front axle maintenance, see Ch. 9 On vehicles, a two-section cardan shaft with an average support and three cardan joints is installed on the side of the...

Cardan shaft — removal and installation
1. Raise the rear of the car as well. 2. Mark the mutual position of the flanges of the rear section of the cardan shaft and the drive gear of the gearbox (photo). 11.2...

Middle support — replacement
1. Unscrew the two nuts of the support bracket, remove both halves of the bracket. 2. Mark the relative position of the flanges of the front and rear sections of the...

Cardan joints — replacement
Attention! Cardan joints on parts of cars cannot be replaced. Before dismantling the cardan shaft, consult your parts supplier. The retaining rings of the bearings of...

Axle shaft, rear wheel bearing and oil seal — removal and installation
Removing 1. Raise the rear of the vehicle. 2. Remove wheels. 3. Remove the brake drum ( Ch. 10 ). 4. Disconnect the parking brake cable and hydraulic line ( Ch. 10 ). 5....

Rear axle gearbox — removal and installation
Attention! This description only applies to plug-in gearboxes that are mounted in the axle beam. A non-separable rear axle is installed on a part of the cars, the repair...

Reducer drive gear oil seal — replacement
1. Drain the gearbox oil. 2. Raise the rear of the car, install stands under the frame and gearbox housing. 3. Disconnect the cardan shaft from the gearbox and move it...

Rear axle — removal and installation
Removing 1. Raise the rear of the vehicle and place stands under the body. 2. Jack up the rear axle under the gear housing. 3. Remove wheels. 4. Disconnect the cardan...